Symetrix EDGE Frame

Symetrix EDGE Frame
Symetrix EDGE Frame
Introduction

Edge

  • A Powerful DSP Featuring Flexible I/O Configuration
  • 128 Channel (64×64) Redundant Dante
  • On-board Ethernet and Dante Network Switches
  • 4 I/O Expansion Card Slots
 

Features
Specifications
Features
  • Dante™ in Our DNA. Edge DSPs are equipped with 128 (64×64) redundant Dante channels. The Dante protocol enables ultra-reliable multi-channel audio networking over IP. Together, Symetrix and Dante provide the fastest possible way to implement, control, and maintain a system of networked DSPs and accessories – including third party Dante-enabled microphones, loudspeakers, power amps, and mixing consoles.
  • Total Input/Output Flexibility. Four versatile option card slots enable unique I/O configurations – aligning the hardware with exact system requirements.  Optional cards support analog and AES-3 digital I/O as well as special purpose interfaces including AEC, VoIP, analog telephone, and USB.
  • On-board 10/100 and Gigabit Switches. Unique to Symetrix Radius and Edge DSPs, built in switches lower system cost, reduce or eliminate the need for peripheral switches, and increase system reliability.
  • Unlimited Programming Flexibility. Edge is programmed using Composer – Symetrix’ award winning open-architecture CAD application. Unique to Composer is the ability to natively configure Symetrix and select third party Dante hardware – thereby eliminating the confusion of multiple or redundant software applications.
  • Control Made Easy. Multiple control options include low-cost Symetrix ARC wall panels and an easy to generate SymVue Windows virtual GUI. The human readable Composer Control Protocol supports programming of third-party touch screens and control devices.
  • An Embedded Web Server for Status and Even More Control. Edge’s embedded web server displays I/O levels, diagnostics data, and hosts ARC-WEB – a browser-based interface for smart phones, tablets, and computers.
Introduction
Specifications
SPECIFICATIONS

Processors

1 x Analog Devices SHARC 21489 @ 400 MHz SIMD.

Raw processing capacity

400 MIPS, 1.6 GFLOPS.

Sampling Rate

48 kHz, ± 100 ppm.

Frequency Response (A/D/A)

20 Hz – 20 kHz, ± 0.5 dB.

Dynamic Range (A/D/A)

> 114 dB, A-weighted.

Channel Separation (A/D/A)

> 108 dB @ 1 kHz, +24 dBu.

Latency (A/D/A)

0.88 mS, inputs routed to outputs.

Delay memory

174 mono seconds per Edge frame.

Analog control inputs

0-3.3 VDC.

Recommended external control potentiometer

10k Ohm, linear.

Logic outputs

Low (0V) when active, pulled high (5V) when inactive.

Logic output maximum external power supply voltage

24 VDC.

Logic output maximum external power supply current sinking

50 mA.

Logic output maximum output current

10 mA.

RS-232 accessory serial I/O

38.4 kbaud (default), 8 data bits, 1 stop bit, no parity, no flow control wired straight-through, only pins 2, 3, and 5 required.

RS-485 serial I/O

38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port.

Ethernet Cable

Standard CAT5, maximum device to device length = 100 meters.

Dante Cable

Standard CAT6, maximum device to device length = 100 meters.

ARC Cable

Standard CAT5, distance dependent upon load and number of devices.

Maximum devices per system

32 units per Site File.

Maximum stored presets

1000.

CONTACT US
Let us follow up
with you
Our office hours are 9:30am-5:30pm weekdays — please drop by, call us or fill in the contact form so we can reply to you shortly.

Magna-Tech Electronic Co., Inc.
329 Palermo Ave. 1st Floor
Coral Gables, FL 33134-6601 USA
Phone: (305) 573-7339
Fax: (305) 573-8101
E-mail:
Your message was sent succesfully!

Your e-mail

Your message